#1
|
||||
|
||||
Everytime
Everytime at the NOCC show this past weekend that I started up my car, I had guys asking me what motor I had. I told em it was just a 350 with 330 HP crate motor. So then they all asked what cam is in it? I said its fashioned after the 65-67 Corvette 327 with a little more lift & duration. I showed them the paperwork I have on the motor.
My paperwork on the cam says: Duration @ .050": 212° Intake / 222° Exhaust and the Lift: .435" Intake / .460" Exhaust. Not one of those guys (some were drag racers) agreed with those specs. They all said they think its over .500" by the way it lopes. I told them all I know is, if I really nail it, it will just shit n git.
__________________
Today, is the tomorrow you worried about yesterday..enjoy it !!! Last edited by Ken Hayes; 08-03-2015 at 04:36 PM. |
#2
|
|||
|
|||
I built a duplicate of the GM 350/330hp HO crate motor a few months ago...added same GM cam and Vortec heads on a stock, dish piston 350 short block. Installed it in my buddy's '65 Chevelle SS convertible.
It has no where the "lope" you described... Believe me...I KNOW lope when I hear it. https://www.youtube.com/watch?v=rudosIEFnbM https://www.youtube.com/watch?v=Up-cpzPbH7s
__________________
2017 Camaro RS -217 cu in 365 HP w/8 speed auto 1967 Camaro SS -5.3L LS w/4L60E & 4.11 12 bolt 2019 Cadillac XT5 3.6L V6 w/310 HP & 8 speed AWD Last edited by BillsCamino; 08-03-2015 at 08:43 AM. |
#3
|
|||
|
|||
It sounded great ,I did get to hear it once even though you didnt know I was there but then again we were everywhere.It was good to finally get to meet you and Judy in person and see that beautiful car.Great show as usual.
__________________
John |
#4
|
||||
|
||||
Bill, this is just a little snippet of it. Motor is still a little cold. When its warm it "lopes" more than this.
https://youtu.be/B5j33lfUv-4
__________________
Today, is the tomorrow you worried about yesterday..enjoy it !!! |
#5
|
|||
|
|||
That cam sounds more aggressive than the GM HO crate cam....212/222 @ .050" is pretty mild.
What is the idle set at? How much base timing? Where is the vacuum advance hooked up to...ported or manifold source? How much vacuum at idle? I'll get a video of my buddy's '65 the next time I'm near his car. Slightly noticeable lope at idle but clears right up off idle. Are you sure that's a stock GM HO cam?? |
#6
|
||||
|
||||
I have no idea what timing is, vacuum is off of Edlebrock 600 carb. Don't know vacuum @ idle and the idle was at 600 RPM.....I have done nothing to this motor except change plugs in 3 years. As far as I know, its supposed to be the stock cam that came with 350/330 HO crate motor.
__________________
Today, is the tomorrow you worried about yesterday..enjoy it !!! |
#7
|
||||
|
||||
__________________
Today, is the tomorrow you worried about yesterday..enjoy it !!! |
#8
|
||||
|
||||
Sounds good.
__________________
Ray 1970 SS Chevelle Van Nuys Built |
#9
|
|||
|
|||
Maybe the low idle speed adds to the effect?
I had the idle in gear tuned to 625 RPM in my LQ4. It has a baby cam, 202/216 on a 112. It loped enough to make people look around in traffic trying to figure where it was coming from.
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi |
#10
|
||||
|
||||
Thanks Ray.
__________________
Today, is the tomorrow you worried about yesterday..enjoy it !!! |
Thread Tools | |
Display Modes | |
|
|