ChevelleForum.net

Go Back   Chevrolet Chevelle Forums > Chevrolet Chevelle Garage > Electrical

Reply
 
Thread Tools Display Modes
  #1  
Old 11-16-2011, 09:50 AM
SS Shaun SS Shaun is offline
Senior Member
 
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default trunk harness

hey guys can someone do me a favor and show me how the harness from the trunk to the inside of the cab should be ran please? i want to make sure i am running this in the right spot.
here is what my rear looks like now where the seat goes

is this correct? should that metal plate be there?
and not pictured but right above the wheel well is a small square and that is where i have the harness running from the trunk. is that the correct spot?
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #2  
Old 11-16-2011, 03:10 PM
Hank70SS's Avatar
Hank70SS Hank70SS is offline
Moderator
 
Join Date: Dec 2009
Location: Brighton, MI
Posts: 4,719
Default

There should be a cardboard divider instead of what you have there, looks to be metal. It hangs on the metal divider where the seat back hooks. You can the see the cardboard through the holes in the metal. If you want one you can get the divider from just about any of the suppliers.

In the post linked below you can see where the wiring comes into the trunk.

http://chevelleforum.org/showthread....ighlight=trunk
__________________
Hank

70 Chevelle SS396(454), M20, 3.73
My Chevelle
Reply With Quote
  #3  
Old 11-16-2011, 05:01 PM
SS Shaun SS Shaun is offline
Senior Member
 
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default

thanks a lot man! but my trunk looks nothing like that i will snap some pics and show you
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #4  
Old 11-16-2011, 05:52 PM
Hank70SS's Avatar
Hank70SS Hank70SS is offline
Moderator
 
Join Date: Dec 2009
Location: Brighton, MI
Posts: 4,719
Default

Sorry, forgot you have a 69, not a 70. Maybe someone else with a 69 can shoot some pics for you.
__________________
Hank

70 Chevelle SS396(454), M20, 3.73
My Chevelle
Reply With Quote
  #5  
Old 11-16-2011, 07:43 PM
shadowgray396's Avatar
shadowgray396 shadowgray396 is offline
Senior Member
 
Join Date: Dec 2009
Location: Oregon City, Oregon
Posts: 6,062
Default

68 to 72 use the same trunk divider, your does not look correct. The wiring harness should run along the bottom of the floor pan and have clips that hold it in place as it comes up the floor pan to the trunk.

http://www.ss396.com/mm5/merchant.mv...uct_Code=ITD-9
__________________
Ray
1970 SS Chevelle Van Nuys Built

Last edited by shadowgray396; 11-17-2011 at 07:46 AM.
Reply With Quote
  #6  
Old 11-16-2011, 10:01 PM
SS Shaun SS Shaun is offline
Senior Member
 
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default

here is what my trunk looks like


let me know what you think
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #7  
Old 11-17-2011, 06:31 AM
Hank70SS's Avatar
Hank70SS Hank70SS is offline
Moderator
 
Join Date: Dec 2009
Location: Brighton, MI
Posts: 4,719
Default

Looks like someone replaced or covered the metal divider. It's definitely not solid, should like similar to mine. Also on the inside, the screws or rivets aren't a factory thing.
__________________
Hank

70 Chevelle SS396(454), M20, 3.73
My Chevelle
Reply With Quote
  #8  
Old 11-17-2011, 07:34 AM
SS Shaun SS Shaun is offline
Senior Member
 
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default

so this leads me to my next question. might be a new topic but i need to know can i put my back seats in with this kind of back?
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #9  
Old 11-17-2011, 07:54 AM
shadowgray396's Avatar
shadowgray396 shadowgray396 is offline
Senior Member
 
Join Date: Dec 2009
Location: Oregon City, Oregon
Posts: 6,062
Default

This is what the inside of my trunk looks like looking forward. Just not sure how strong it is if they cut out the original metal from the pictures. Otherwise the only time you will know something is different is only when the trunk is open, you will never know from inside the car.

__________________
Ray
1970 SS Chevelle Van Nuys Built

Last edited by shadowgray396; 11-17-2011 at 07:57 AM.
Reply With Quote
  #10  
Old 11-17-2011, 08:28 AM
SS Shaun SS Shaun is offline
Senior Member
 
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default

do any of those holes have anything to do with putting the rear seat in?
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:48 AM.



Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Audiokarma.org