man has it been that long since i updated!! i will take pictures tomorrow and update this thread! my chevelle is going to be back on all 4 tomorrow as long as i have the whole day to myself :)

i waited all morning for my part and it never showed up! so here is what i did today
http://i114.photobucket.com/albums/n...-35-00_845.jpg
new wheel lug finally in and wheels installed until i figure out if i want to keep them or not
cleaned the inside of the car because i needed to do it to make me feel better
http://i114.photobucket.com/albums/n...9-19-59_83.jpg
http://i114.photobucket.com/albums/n...-19-49_264.jpg

then at 8pm look what shows up
http://i114.photobucket.com/albums/n...9-52-55_98.jpg
the part i waited for finally showed up when i am cleaning up and getting ready to eat dinner!..lol

did not have much time today but i took out my 4 speed manual trans to get it ready for the 6 speed
http://i114.photobucket.com/albums/n...-46-53_324.jpg

http://i114.photobucket.com/albums/n...-47-02_825.jpg

http://i114.photobucket.com/albums/n...19-47-53_2.jpg

http://i114.photobucket.com/albums/n...-48-04_360.jpg

not going to have much time this week to do it but i am hoping to have it in by sunday!

well its been a LONG time since i had time to work on my chevelle. But i finally got the t56 under the car and INSTALLEd very little cutting. about as much as putting in a tko
http://i114.photobucket.com/albums/n...-56-03_890.jpg

got a new (well used but new for me) intake
http://i114.photobucket.com/albums/n...-10-51_276.jpg
installed the starter in wrong
http://i114.photobucket.com/albums/n...-02-54_774.jpg

and so happy i found the right bolts to move it over
http://i114.photobucket.com/albums/n...-28-58_635.jpg

now that its in correct i can work on putting the t56 in
http://i114.photobucket.com/albums/n...-47-49_413.jpg

http://i114.photobucket.com/albums/n...-48-04_360.jpg

this is all i had to cut for the t56

now that i got that done i said i was going to work on my brake system
so i started from the rear
new hard lines and not pictured but the new rubber line too
http://i114.photobucket.com/albums/n...-58-57_338.jpg

new front brakes and bearings
http://i114.photobucket.com/albums/n...e/IMG_8770.jpg

new rubber lines and metal lines
http://i114.photobucket.com/albums/n...e/IMG_8771.jpg

new metal lines waiting for the hold off valve
http://i114.photobucket.com/albums/n...e/IMG_8772.jpg

new booster and master (and yes its painted)
http://i114.photobucket.com/albums/n...e/IMG_8773.jpg

new dis block on the frame with all new lines as well
http://i114.photobucket.com/albums/n...e/IMG_8774.jpg

passenger side metal and rubber lines
http://i114.photobucket.com/albums/n...e/IMG_8776.jpg

ran in the stock locations
http://i114.photobucket.com/albums/n...e/IMG_8777.jpg

new metal line from the dis block to the rear
http://i114.photobucket.com/albums/n...e/IMG_8778.jpg

and t56 on the trans brace now just waiting for the drive shaft
http://i114.photobucket.com/albums/n...e/IMG_8782.jpg

It could be the picture but your distribution block is looking way to close to your headers. I have read where it needs to be moved when using headers. Otherwise looking good.

yeah i have to bend it back because when i was trying to get the one on the bottom loose i bent the arm that holds it in place.

got the wheels for the chevelle. I need to get the correct lugs for it but here they are
17x8 all around with 255/45/17s on it for now
http://i114.photobucket.com/albums/n...-58-43_433.jpg