|
|
|
|
|
#1
06-02-2013, 09:54 AM
|
||||
|
||||
Bill, great find on the build sheet. I had my back seat out with no luck. I haven't checked the front yet.
Well, it's been a few days, but I got my new chrome clips for around my front and back glass, got everything fitted and the glass glued in. I started stripping the hood in preparation for a little body work and made a set of mufflers for the exhaust. I'm just about ready to take it down the road!
__________________
Alan 1964 Chevelle SS Speed's expensive, how fast do you want to go? 
|
|
#2
06-02-2013, 03:23 PM
|
|||
|
|||
|
Installed a pair of Monroe Quick struts on the front of my Chevy van today...only took FOUR hours!!
 Oh the pain....could have swapped engines in the Chevelle in that amount of time.
__________________
2017 Camaro RS -217 cu in 365 HP w/8 speed auto 1967 Camaro SS -5.3L LS w/4L60E & 4.11 12 bolt 2019 Cadillac XT5 3.6L V6 w/310 HP & 8 speed AWD
|
|
#3
06-02-2013, 10:39 PM
|
|||
|
|||
|
I finished fitting the drivers outer wheelhouse piece and welded it in. I also reshaped the drivers trunk drop off, fitted it, and welded it in. I also split the face of the outer rocker replacement and welded it back so that the face of it was the same as stock. The rocker I got was .080 more narrow across the face of it.
|
|
#4
06-05-2013, 06:03 PM
|
|||
|
|||
|
Dropped a pair of Sportsman II SBC heads off at my machinist's shop for freshening up and installing a new set of Comp hyd roller springs, retainers, and locks.
Working on building another 383 stroker roller small block engine. For what, I don't know yet... 
__________________
2017 Camaro RS -217 cu in 365 HP w/8 speed auto 1967 Camaro SS -5.3L LS w/4L60E & 4.11 12 bolt 2019 Cadillac XT5 3.6L V6 w/310 HP & 8 speed AWD
|
|
#5
06-05-2013, 06:34 PM
|
|||
|
|||
|
Quote:
|
|
#7
06-06-2013, 06:19 PM
|
||||
|
||||
|
Looking Good
__________________
Ray 1970 SS Chevelle Van Nuys Built
|
|
#8
06-07-2013, 06:18 PM
|
||||
|
||||
|
Made plans to have new springs put on the front. When they were installed last year we only cut 1/2 a coil off, but they settled A LOT. Bummer. So we start all over, I told grumpy that we are not going to cut them at all, he said that it will probably look funny. So as soon as I have them in I will take a pic and we will see what you guys think.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving ! For the audio geek try: www.audiokarma.org
|
|
#10
06-08-2013, 08:12 PM
|
||||
|
||||
|
Thought about it, especially while sitting in traffic driving my van. flash...I hope your weather clears soon.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving ! For the audio geek try: www.audiokarma.org
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Hybrid Mode
