ChevelleForum.net

Go Back   Chevrolet Chevelle Forums > Chevrolet Chevelle Car Talk > Chevelle General Talk
Reload this Page What Did You Do To Your Chevelle Today
Register FAQ Chevelle Chat Room Community Calendar

Reply
Page 12 of 317 « First 21011 12 13142262112 Last »
 
Thread Tools Display Modes
  #1  
Old 10-14-2011, 09:28 AM
Ms Grumpy's Avatar
Ms Grumpy Ms Grumpy is offline
Bowtie Member
  
Join Date: Dec 2009
Location: Just outside San Antonio, Texas
Posts: 7,403
Default
Wow. Isn't it nice when something is easy to find.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving !

For the audio geek try: www.audiokarma.org

Reply With Quote
  #2  
Old 10-14-2011, 09:53 AM
fleming23's Avatar
fleming23 fleming23 is offline
Senior Member
  
Join Date: Nov 2010
Location: Hiram, GA
Posts: 612
Default
Hope to go pick my car up later today so I can try to get it cleaned up in time for a show tomorrow.
__________________
Eric
496 cu. in. "cruiser"
Assembled & tuned by Mo's Speed Shop - Dallas, GA
Reply With Quote
  #3  
Old 10-14-2011, 10:00 AM
SS Shaun SS Shaun is offline
Senior Member
  
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default
ordered a few things today my new sending unit, gasket and the hold down for it. sunday i am going to clean the tank and check for holes and rust and then paint it. what do you guys think for the paint? ryno lining since i have a whole can left from doing my father in laws truck bed...lol
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #4  
Old 10-14-2011, 07:39 PM
SS Shaun SS Shaun is offline
Senior Member
  
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default
spent an hour and a half but after i was done i was happy


rear bumper is on
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #5  
Old 10-14-2011, 09:03 PM
flash flash is offline
Senior Member
  
Join Date: Dec 2009
Location: Canton Georgia
Posts: 8,349
Default
I drove Joans vert to town after work and gave it a quick spray bath ,then I picked her up from work and took her to dinner and to the grocery store .Any excuse to drop the top and go for a ride.
__________________

John
Reply With Quote
  #6  
Old 10-15-2011, 07:42 AM
BillsCamino BillsCamino is offline
Senior Member
  
Join Date: Dec 2009
Location: Marietta, GA 30066
Posts: 1,550
Send a message via AIM to BillsCamino
Default
Quote:
Originally Posted by fleming23 View Post
Hope to go pick my car up later today so I can try to get it cleaned up in time for a show tomorrow.
Quote:
Originally Posted by flash View Post
I drove Joans vert to town after work and gave it a quick spray bath ,then I picked her up from work and took her to dinner and to the grocery store .Any excuse to drop the top and go for a ride.
Y'all going to Riverstone tonight?? We'll be there...
__________________
2017 Camaro RS -217 cu in 365 HP w/8 speed auto
1967 Camaro SS -5.3L LS w/4L60E & 4.11 12 bolt
2019 Cadillac XT5 3.6L V6 w/310 HP & 8 speed AWD
Reply With Quote
  #7  
Old 10-15-2011, 08:42 PM
flash flash is offline
Senior Member
  
Join Date: Dec 2009
Location: Canton Georgia
Posts: 8,349
Default
We went to the local cruise in and hooked up with Wild Bill ,and Dewayne and their better halves ,sure was good to see them. Also took Chase and his girlfriend for a ride in Joans vert.
__________________

John
Reply With Quote
  #8  
Old 10-18-2011, 09:53 PM
SS Shaun SS Shaun is offline
Senior Member
  
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default
so today i had about an hour to kill so i went to the garage to check on my rear end i wanted to find out what i had for sure. so i popped the cover off and here is what i found



4.11 gears with a Spool but then i found this


they are axles that can handle over 500ft tq so i think i will be good with these axles when i get the posi rear


so tomorrow if i can find another hour i will pull out the axle on one side and count the splines on my axle so i can order my new posi rear
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #9  
Old 10-21-2011, 08:46 AM
SS Shaun SS Shaun is offline
Senior Member
  
Join Date: Mar 2011
Location: poconos pa
Posts: 1,921
Send a message via AIM to SS Shaun
Default
pulled out my axle lastnight to see how many splines i have to order my new rear posi
__________________
2005 dodge magnum daily driver
1988 mazda rx7 LS6 swap
1969 SS work in progress
Reply With Quote
  #10  
Old 10-21-2011, 10:20 AM
Rharp Rharp is offline
Senior Member
  
Join Date: May 2011
Posts: 159
Default
I put new valve cover gaskets on yesterday.
I have a small oil leak that drips down from the front of the bell housing.
I have climbed under the car but could not locate the source.
When I stated looking around up top I noticed some moisture on the back of the valve cover, I figured what the heck I'll start there.
I'm not much of a wrench so I either fixed it or made it worse.
__________________
Rich
Reply With Quote
Reply
Page 12 of 317 « First 21011 12 13142262112 Last »

« Previous Thread | Next Thread »

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:17 PM.

Contact Us - Chevrolet Chevelle Forums - Archive - Top


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Audiokarma.org