|
|
|
|
|
#1
07-21-2014, 07:08 PM
|
||||
|
||||
Very clean looking setup
__________________
Ray 1970 SS Chevelle Van Nuys Built 
|
|
#2
07-22-2014, 07:23 AM
|
|||
|
|||
|
Eric,
If the local guy doesn't buy your A/C stuff and you and Carpoor can work out a deal...I can drag it all down to Daytona for the Turkey Rod Run in Nov. I may even attend the NPD GM show in Silver Springs, FL in Oct. Assuming Carpoor isn't in an immediate need for it...
__________________
2017 Camaro RS -217 cu in 365 HP w/8 speed auto 1967 Camaro SS -5.3L LS w/4L60E & 4.11 12 bolt 2019 Cadillac XT5 3.6L V6 w/310 HP & 8 speed AWD Last edited by BillsCamino; 07-22-2014 at 07:25 AM.
|
|
#3
07-22-2014, 03:04 PM
|
|||
|
|||
|
Thanks Bill! Eric, let me know if he doesn't take it. No rush at all, would be buying it and setting it aside for the 72' I just bought my dad.
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi
|
|
#4
07-22-2014, 03:05 PM
|
|||
|
|||
|
Quote:
|
|
#5
07-25-2014, 05:11 PM
|
|||
|
|||
|
Quote:
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi
|
|
#7
07-24-2014, 04:15 PM
|
|||
|
|||
|
Touched up the paint on my engine, installed starter. Rolled it back over, lifters installed, push rods installed, rocker arms installed, poly locks finger tight.
Still much to do before it goes back in the car, but I haven't had much time lately. Luckily, I am almost at my 40 for the week. So I "should" be home early tomorrow, an in turn have time to work on the car.
__________________
1972 SS 454 Chevelle LS5/M21/12 bolt 3.73 posi 1969 Malibu COPO L72/M20/12 bolt 3.31 posi 1968 Malibu LQ9/4L80E/12 bolt 3.73 posi
|
|
#9
07-24-2014, 09:26 PM
|
||||
|
||||
|
I was working on the costume for the NOCC show for my car. I hope it turns out good.
__________________
Get in, sit down, shut up, hold on...cause Ms Grumpy is driving ! For the audio geek try: www.audiokarma.org
|
|
#10
07-25-2014, 07:55 AM
|
|||
|
|||
|
installed new lines for my oil pressure gauge cleaned up some wiring. figured i'd do that before i put my fenders back on..lol today i think i am going to install my heater box so that is out of the way as well
__________________
2005 dodge magnum daily driver 1988 mazda rx7 LS6 swap 1969 SS work in progress
|
 |
|
|
Hybrid Mode
